On this page10
Press brake maintenance in the UAE comes down to four habits: keep it clean, keep the oil right, lubricate on schedule and inspect before small faults grow. Heat and dust in UAE workshops make the oil and the filters work harder, so the checks below matter more here. This guide gives a daily, weekly, monthly and yearly schedule you can print for the machine. TFI has built metalworking machines since 1965.
Press brake maintenance schedule
Press brake maintenance schedule
Every day
- What to do
- Check the hydraulic oil level; clean the bed, the tools and the back gauge fingers; test the light curtain or guards and the emergency stop; listen for new noise
- Why
- Low oil lets air in and makes the ram move unevenly; dirt on the tools marks the parts
Every week
- What to do
- Lubricate the ram guides and the back gauge screws and guides; check for loose bolts and fasteners
- Why
- Dry guides wear and lose accuracy
Every month
- What to do
- Lubricate the cylinder pins; check hoses and fittings for leaks; check the oil tank for water; clean the cooler and the electrical cabinet filter
- Why
- Leaks and water in the oil damage valves and seals; dust makes electrics run hot
Every year
- What to do
- Change the hydraulic oil and the filters, or when the manual or an oil analysis says; full inspection of cylinders, seals and electrics; check the back gauge and the ram parallelism
- Why
- Old oil and full filters wear the pump and valves; the checks keep the bend angles right
New machine
- What to do
- First oil and filter change after the first month of work, if the manual says so
- Why
- Removes the particles of running in
Press brake maintenance schedule
Every day
- What to do
- Check the hydraulic oil level; clean the bed, the tools and the back gauge fingers; test the light curtain or guards and the emergency stop; listen for new noise
- Why
- Low oil lets air in and makes the ram move unevenly; dirt on the tools marks the parts
Every week
- What to do
- Lubricate the ram guides and the back gauge screws and guides; check for loose bolts and fasteners
- Why
- Dry guides wear and lose accuracy
Every month
- What to do
- Lubricate the cylinder pins; check hoses and fittings for leaks; check the oil tank for water; clean the cooler and the electrical cabinet filter
- Why
- Leaks and water in the oil damage valves and seals; dust makes electrics run hot
Every year
- What to do
- Change the hydraulic oil and the filters, or when the manual or an oil analysis says; full inspection of cylinders, seals and electrics; check the back gauge and the ram parallelism
- Why
- Old oil and full filters wear the pump and valves; the checks keep the bend angles right
New machine
- What to do
- First oil and filter change after the first month of work, if the manual says so
- Why
- Removes the particles of running in
Tip: keep a simple log at the machine: date, hours, what was done and who did it. It shows when the next job is due and helps the service engineer find a fault faster.
Hydraulic care in a hot climate
Oil
use the oil grade in the manual, and keep the tank clean and closed.
Temperature
watch the oil temperature in summer; keep the cooler and its fins clean and the machine out of direct sun.
Filters
change them with the oil, and sooner if the filter indicator shows.
Leaks
a wet hose or fitting is a warning; fix it before it fails.
Oil
use the oil grade in the manual, and keep the tank clean and closed.
Temperature
watch the oil temperature in summer; keep the cooler and its fins clean and the machine out of direct sun.
Filters
change them with the oil, and sooner if the filter indicator shows.
Leaks
a wet hose or fitting is a warning; fix it before it fails.
Tools, back gauge and safety
Tools
clean the punch and die after use, store them on racks, and check the working edges for wear.
Back gauge
keep the screws and guides clean and oiled; check that the fingers stop where the control says.
Safety
never run the press brake with a guard, light curtain or emergency stop out of order.
Tools
clean the punch and die after use, store them on racks, and check the working edges for wear.
Back gauge
keep the screws and guides clean and oiled; check that the fingers stop where the control says.
Safety
never run the press brake with a guard, light curtain or emergency stop out of order.
Signs your press brake needs service
Bend angles change along the part or from part to part.
The ram moves unevenly, slowly, or drifts down.
The oil runs hot, foams, or the pump is louder.
Oil leaks at the cylinders, hoses or valves.
Back gauge positions do not match the control.
Bend angles change along the part or from part to part.
The ram moves unevenly, slowly, or drifts down.
The oil runs hot, foams, or the pump is louder.
Oil leaks at the cylinders, hoses or valves.
Back gauge positions do not match the control.
Then call a service engineer: see press brake servicing in the UAE. TFI services its own press brakes, such as the Abadan press brake (TFI Bend 5).
A clean, well-oiled press brake keeps its bend angles and its value. Most of this schedule takes minutes a day; the yearly work and repairs are for a trained service engineer.
Key points
Who does what
Operator, every day
oil level, cleaning, safety check, noise.
Maintenance technician, weekly and monthly
lubrication, bolts, hoses, oil tank, filters in the cabinet.
Service engineer, yearly or on a fault
oil and filters, cylinders and seals, electrics, back gauge and parallelism.
Operator, every day
oil level, cleaning, safety check, noise.
Maintenance technician, weekly and monthly
lubrication, bolts, hoses, oil tank, filters in the cabinet.
Service engineer, yearly or on a fault
oil and filters, cylinders and seals, electrics, back gauge and parallelism.
Frequently asked questions
Why is maintenance important for press brake machines in the UAE?
Proper maintenance supports the service life and performance of a press brake machine. It helps prevent wear and tear while keeping operations smooth and reliable in demanding industrial environments.
How do I keep my press brake machine clean?
Regularly clean the machine to remove any dirt or debris that may accumulate on its surface or inside its mechanisms. This prevents buildup that could lead to premature wear and keeps it running smoothly.
What lubrication practices should be followed for a press brake?
Follow the manufacturer’s recommendations for lubricating the machine so all moving parts stay lubricated and run smoothly. Consistent lubrication reduces friction and extends component life.
How often should I inspect my press brake machine?
Inspect the machine regularly for any signs of wear. Routine checks allow early detection of issues, helping maintain optimal performance and avoid unexpected downtime.
What should I look for during press brake inspections?
Regularly inspect the machine for any signs of wear on components, check for proper alignment, keep it clean after each use, and verify that lubrication levels are correct according to manufacturer guidelines.
How can I arrange professional maintenance for my press brake in the UAE?
If you are ready to apply these maintenance steps or need expert support for your press brake, start with live chat for immediate guidance, fill out the inquiry form on our website, or call our team to schedule professional service tailored to your machine.
TFI press brake machine on video
The TFI Abadan hydraulic press brake machine, from the TFI Co. YouTube channel.
Ask TFI for a quote
Send the material, thickness and length you work with, and ask TFI for the datasheet and a quotation.

Talk to TFI about your press brake service
Ask TFI for more. Send the material, thickness and length you work with, chat with us on Telegram or call us, and ask for the datasheet and a quotation.
On social media
On social media
- Section
- Industrial Machines for UAE
- Updated
- 15 November 2026
- Reading time
- 5 min read
Discuss this with our team
Tell us what you need: call us or chat on Telegram, and our team gets back to you.
Send an enquiry
