On this page9
TFI services shearing machines in the UAE: guillotine and swing beam shears, TFI machines and other makes. A service brings back a clean, square cut: the engineer sets the blade gap, checks the blades, the hold-down and the back gauge, and goes through the hydraulics and the electrics. TFI has built metalworking machines since 1965.
What a shear service covers
What a shear service covers
Part of the machineWhat the service engineer checks
- Blades
- Edge condition and chipping; when to regrind or change them; blade bolts tight
- Blade gap
- Gap between upper and lower blade measured with a feeler gauge along the length and set to the material
- Hold-down
- Every hold-down foot presses evenly and holds the sheet during the cut
- Back gauge
- Stops at the size the control shows; guides and screws clean and lubricated
- Cutting angle (guillotine)
- Adjustment works and is set to the material and thickness
- Hydraulics
- Oil level and condition, filters, leaks at hoses, valves and cylinders, pressure
- Guides and pins
- Greased at the grease points; wear and play
- Electrics and safety
- Guards, light curtain or barrier, emergency stop, foot pedal, control panel
- Test
- Test cuts in your material; cut edge and squareness checked with you
What a shear service covers
Part of the machineWhat the service engineer checks
- Blades
- Edge condition and chipping; when to regrind or change them; blade bolts tight
- Blade gap
- Gap between upper and lower blade measured with a feeler gauge along the length and set to the material
- Hold-down
- Every hold-down foot presses evenly and holds the sheet during the cut
- Back gauge
- Stops at the size the control shows; guides and screws clean and lubricated
- Cutting angle (guillotine)
- Adjustment works and is set to the material and thickness
- Hydraulics
- Oil level and condition, filters, leaks at hoses, valves and cylinders, pressure
- Guides and pins
- Greased at the grease points; wear and play
- Electrics and safety
- Guards, light curtain or barrier, emergency stop, foot pedal, control panel
- Test
- Test cuts in your material; cut edge and squareness checked with you
Every service starts with the machine locked out and the power off. Clearances and settings follow the manual of your machine.
Shear machine servicing in pictures




Signs your shear needs service
The cut edge has burrs or is torn.
Blanks are not square or not to size.
The sheet slips during the cut.
The beam moves slowly, unevenly or does not return.
Oil leaks or the oil runs hot.
Unusual noise in the cut.
The cut edge has burrs or is torn.
Blanks are not square or not to size.
The sheet slips during the cut.
The beam moves slowly, unevenly or does not return.
Oil leaks or the oil runs hot.
Unusual noise in the cut.
Blades and parts from TFI
TFI makes shear blades and supplies spare parts for TFI shears. For other makes, send TFI the blade size (length, width, thickness) and the machine model.
How to book a service
Tell TFI about the machine
make, model, year, and a photo of the nameplate.
Describe the problem
what happens, when it started, a photo or a short video.
TFI replies with the next step
advice, a visit, or parts, with a quotation.
Service on site
the engineer checks, adjusts and repairs, then tests the machine with you.
Tell TFI about the machine
make, model, year, and a photo of the nameplate.
Describe the problem
what happens, when it started, a photo or a short video.
TFI replies with the next step
advice, a visit, or parts, with a quotation.
Service on site
the engineer checks, adjusts and repairs, then tests the machine with you.
Choosing a guillotine shear: benefits and sizing. TFI's own guillotine shear: the Kerman shearing machine (TFI Shear 7). All services: machine servicing in the UAE.
TFI shearing machine on video
A TFI shearing machine in the workshop, from the TFI Co. YouTube channel.
Frequently asked questions
Does TFI service shears of other makes?
Yes, ask TFI with the make and model; send a photo of the nameplate.
How often should a shear be serviced?
Follow the manual of your machine; a yearly service plus daily care is a common practice. Call earlier when you see the signs above.
What is the blade gap?
The small gap between the upper and lower blade. It is set to the material and thickness; a wrong gap gives burrs and can damage the blades.
Can TFI supply blades for my shear?
Yes. Send the blade size and machine model.
Ask TFI for a quote
Send the make and model of your shear, a photo of its nameplate and what goes wrong. TFI replies with advice, a visit date or parts, with a quotation.

Talk to TFI about your shear service
- Section
- Machine Servicing in the UAE – TFI Co
- Updated
- 15 November 2026
- Reading time
- 3 min read
Discuss this with our team
Tell us what you need: call us or chat on Telegram, and our team gets back to you.
Send an enquiry