On this page9
  1. A crusher for each stage, with a quotation
  2. Jaw, cone, impact, VSI: 4 types compared
  3. How to choose a crusher
  4. Feed and output: up to 800 t/h*
  5. Typical crushing lines
  6. The TFI crusher range
  7. Frequently asked questions
  8. Ask TFI for a quote
  9. Talk to TFI about your crushing line

Four types of crushers do the work in a stone or concrete line: the jaw, the cone, the impact and the vertical shaft impact (VSI) crusher. Each breaks rock its own way, at one stage of the line.

This guide shows which one suits your rock, your feed and the product you sell. TFI has built metalworking machines since 1965.

A crusher for each stage, with a quotation

Send the rock or concrete, the largest stone you feed, the product sizes and the tonnes per hour. TFI replies with the right crusher for each stage and a quotation.

Jaw, cone, impact, VSI: 4 types compared

Types of crushers compared

  • Jaw crusher

    How it crushes
    Squeezes stone between a fixed and a moving jaw
    Stage in the line
    Primary: the first break
    Suits
    Any rock, hard or soft
    Product
    Coarse stone for the next crusher
  • Cone crusher (TFI Hydrocone)

    How it crushes
    Squeezes stone between a gyrating cone and a fixed bowl
    Stage in the line
    Secondary and fine crushing
    Suits
    Hard, abrasive rock: granite, basalt, river gravel
    Product
    Aggregate set by the output gap
  • Impact crusher

    How it crushes
    A fast rotor throws stone against breaker plates
    Stage in the line
    Primary or secondary
    Suits
    Softer, less abrasive rock: limestone; concrete for recycling
    Product
    Cubical aggregate
  • VSI crusher

    How it crushes
    A rotor throws stone against a rock lining (rock on rock)
    Stage in the line
    Last stage
    Suits
    Small feed of most rock types
    Product
    Manufactured sand and shaped chips

Types of crushers compared

  • Jaw crusher

    How it crushes
    Squeezes stone between a fixed and a moving jaw
    Stage in the line
    Primary: the first break
    Suits
    Any rock, hard or soft
    Product
    Coarse stone for the next crusher
  • Cone crusher (TFI Hydrocone)

    How it crushes
    Squeezes stone between a gyrating cone and a fixed bowl
    Stage in the line
    Secondary and fine crushing
    Suits
    Hard, abrasive rock: granite, basalt, river gravel
    Product
    Aggregate set by the output gap
  • Impact crusher

    How it crushes
    A fast rotor throws stone against breaker plates
    Stage in the line
    Primary or secondary
    Suits
    Softer, less abrasive rock: limestone; concrete for recycling
    Product
    Cubical aggregate
  • VSI crusher

    How it crushes
    A rotor throws stone against a rock lining (rock on rock)
    Stage in the line
    Last stage
    Suits
    Small feed of most rock types
    Product
    Manufactured sand and shaped chips

How to choose a crusher

  1. Know your rock.

    Hard, abrasive rock (granite, basalt, quartzite) wears an impact crusher fast: choose a jaw and then a cone. Softer rock such as limestone, and concrete for recycling, suit an impact crusher.

  2. Measure the largest stone you feed.

    It must pass the crusher's feed opening. Large blasted rock goes to a jaw first.

  3. Name the product you sell.

    Coarse base material, graded aggregate, or sand. Shape matters for concrete and asphalt: impact and VSI crushers give a more cubical product.

  4. Set the output in tonnes per hour.

    Pick the size of each crusher so no stage holds up the line.

  1. Know your rock.

    Hard, abrasive rock (granite, basalt, quartzite) wears an impact crusher fast: choose a jaw and then a cone. Softer rock such as limestone, and concrete for recycling, suit an impact crusher.

  2. Measure the largest stone you feed.

    It must pass the crusher's feed opening. Large blasted rock goes to a jaw first.

  3. Name the product you sell.

    Coarse base material, graded aggregate, or sand. Shape matters for concrete and asphalt: impact and VSI crushers give a more cubical product.

  4. Set the output in tonnes per hour.

    Pick the size of each crusher so no stage holds up the line.

Feed and output: up to 800 t/h*

TFI crushers: largest feed, product and output in t/h*

  • TFI Jaw

    Largest feed*
    Feed opening 100 × 100 to 1200 × 1500 mm
    Output setting or product*
    Coarse stone
    Output*
    0.05 to 800 t/h
  • TFI Impact

    Largest feed*
    Stone up to 120 to 300 mm, by model
    Output setting or product*
    Cubical aggregate
    Output*
    60 to 300 t/h
  • TFI Hydrocone

    Largest feed*
    Stone from the jaw
    Output setting or product*
    Closed side setting 6 to 51 mm
    Output*
    Ask TFI
  • TFI VSI

    Largest feed*
    Feed up to 40 or 50 mm, by model
    Output setting or product*
    Sand and shaped chips
    Output*
    25 to 583 t/h

TFI crushers: largest feed, product and output in t/h*

  • TFI Jaw

    Largest feed*
    Feed opening 100 × 100 to 1200 × 1500 mm
    Output setting or product*
    Coarse stone
    Output*
    0.05 to 800 t/h
  • TFI Impact

    Largest feed*
    Stone up to 120 to 300 mm, by model
    Output setting or product*
    Cubical aggregate
    Output*
    60 to 300 t/h
  • TFI Hydrocone

    Largest feed*
    Stone from the jaw
    Output setting or product*
    Closed side setting 6 to 51 mm
    Output*
    Ask TFI
  • TFI VSI

    Largest feed*
    Feed up to 40 or 50 mm, by model
    Output setting or product*
    Sand and shaped chips
    Output*
    25 to 583 t/h

Output depends on the rock (hardness, moisture, the size of the feed) and on the output setting: hard, abrasive rock such as granite or basalt gives less than limestone. Send TFI your rock and the product sizes you need.

Typical crushing lines

Typical crushing lines

Your materialA typical line

Hard rock: granite, basalt
Jaw → cone → VSI for sand
Limestone and softer rock
Jaw → impact, or impact alone for smaller feed
Concrete and demolition waste
Jaw or impact crusher
River gravel
Jaw for the large stones → cone → VSI for sand

Typical crushing lines

Your materialA typical line

Hard rock: granite, basalt
Jaw → cone → VSI for sand
Limestone and softer rock
Jaw → impact, or impact alone for smaller feed
Concrete and demolition waste
Jaw or impact crusher
River gravel
Jaw for the large stones → cone → VSI for sand

TFI crushers work with feeders, screens and belt conveyors in one line: see the TFI stone and concrete crusher production lines.

The TFI crusher range

The TFI crusher range

  • TFI Jaw

    Job
    Primary crushing
    Sizes*
    23 models, feed opening 100 × 100 to 1200 × 1500 mm
    Output*
    0.05 to 800 t/h
  • TFI Impact

    Job
    Primary or secondary crushing, recycling
    Sizes*
    7 models, rotor Ø 1000 to 1400 mm
    Output*
    60 to 300 t/h
  • TFI Hydrocone

    Job
    Secondary and fine crushing of hard rock
    Sizes*
    Output setting 6 to 51 mm, 132 to 300 kW
    Output*
    Ask TFI
  • TFI VSI (rock on rock)

    Job
    Sand making and shaping
    Sizes*
    6 models, rotor Ø 650 to 1260 mm
    Output*
    25 to 583 t/h

The TFI crusher range

  • TFI Jaw

    Job
    Primary crushing
    Sizes*
    23 models, feed opening 100 × 100 to 1200 × 1500 mm
    Output*
    0.05 to 800 t/h
  • TFI Impact

    Job
    Primary or secondary crushing, recycling
    Sizes*
    7 models, rotor Ø 1000 to 1400 mm
    Output*
    60 to 300 t/h
  • TFI Hydrocone

    Job
    Secondary and fine crushing of hard rock
    Sizes*
    Output setting 6 to 51 mm, 132 to 300 kW
    Output*
    Ask TFI
  • TFI VSI (rock on rock)

    Job
    Sand making and shaping
    Sizes*
    6 models, rotor Ø 650 to 1260 mm
    Output*
    25 to 583 t/h

Frequently asked questions

Which type of crusher is used first?

Usually the jaw crusher. It takes the largest stone and breaks it down for the next crusher.

Cone or impact crusher?

For hard, abrasive rock a cone crusher wears less. For softer rock and concrete recycling an impact crusher gives a more cubical product.

What does a VSI crusher do?

It throws small stone against a lining of rock at high speed. The result is manufactured sand and well-shaped chips.

How do I size a crushing line?

Send TFI your rock, the largest stone you feed, the products you sell and the tonnes per hour you need. TFI answers with the line and the model for each stage.

Ask TFI for a quote

Send TFI your rock or material, the largest stone you feed, the product sizes you sell and the tonnes per hour you need. TFI answers with a line, a model for each stage and a quotation.

contact us

Fill in the form below - a real person reads every answer.

  • 11 questions
  • About 2 minutes
Salutation
How should TFI reply? (optional)

Material, thickness and length, or the machine you have in mind. A photo or drawing can follow on Telegram.

Salutation
How should TFI reply? (optional)

Material, thickness and length, or the machine you have in mind. A photo or drawing can follow on Telegram.

We use your answers only to reply to you. They are kept for 425 days. Your answers stay on this device for 24 hours until you send them. Cloudflare checks that this form is sent by a person. How Cloudflare handles it

What happens next

  1. We read your request, usually the same working day.
  2. A specialist replies with answers or a few questions.
  3. You decide - no obligation.
QR code that opens a Telegram chat with TFI Co at t.me/tfico
Scan to chat with TFI on Telegram (t.me/tfico)

Talk to TFI about your crushing line

Send TFI your rock or material, the largest stone you feed, the product sizes you sell and the tonnes per hour you need. TFI answers with a line, a model for each stage and a quotation.

Section
TFI Stone and Concrete Crusher Production Lines
Updated
18 November 2026
Reading time
4 min read

Discuss this with our team

Tell us what you need: call us or chat on Telegram, and our team gets back to you.

Send an enquiry